|
Excess moisture and humidity within a buildings environment or in its structural
element is usually the cause of the greatest damage such as rot, mold growth,
decrease in structural strength, reduced insulation values, failure of flooring
, roofing and wall support etc. A building or home inspector needs to be able
to quickly locate, evaluate and pin point these areas of excess moisture quickly
and accurately, preferably by non-destructive means (without damage to the
material or element being tested).
Moisture Encounter Plus
The Moisture Encounter PLUS MEP is an upgraded version of the world's most
popular and successful non-destructive moisture meter the Moisture Encounter
for Wood, Felt-Roofing, Drywall, Plaster, Brick, Tiles and other materials
such as Paint, Wall Coatings, Drywall, Ceramic Tiles, Floor coverings and ceiling
tiles.
With no probes or pins to cause surface damage, the MEP uses external rubber
electrodes, in direct contact with the surface for best sensitivity and signal
penetration.
 |
Benefits:
- Non-destructive measurement, no surface damage to material being tested.
- Three measurement ranges optimized for testing different materials.
- Deep signal penetration up to 1¼ inches (30mm) to detect elevated moisture through most covering materials without having to damage the material being tested.
- External rubber electrodes make direct contact with material for best sensitivity, repeatability and greater depth of signal penetration.
- Wide range of readings of 5% to 30% on the wood scale and 0 to 100 on the comparative scale for other materials.
- Large, clear, easy to read meter.
- Hold function allows the user to “Freeze” the reading taken in awkward locations.
- Audio Warning Tone for high moisture readings. Can be switched on or off.
- Auto Power-Down switches the meter off when not in use. Preserves battery power.
|
Click for Data Sheet
MRH Moisture and Humidity Measurement Meter (Digital)
A pocket size non-destructive digital display moisture meter for measuring the % moisture content in wood and comparative readings in other building materials. It incorporates a switchable specific gravity adjustment for most wood species, plus it provides relative readings deep into most building materials. such as Drywall, Roofing, Brick, Ceramic tile etc. The MRH also has the additional option of a Hygrometer mode to measure Relative Humidity, Temperature, Dew Point Temperature and Grains/lb.by simply plugging in the optional Tramex Relative Humidity Probe. Allows for use with ASTM F2170 and ASTM F2420. The MRH operates as a pin-type wood meter when used with the WPIE (Wood Probe Interface Electronics) and a Hand or Hammer Electrode.
Click for Data Sheet
Survey Encounter
The world's most advanced and versatile non-destructive moisture meter for measurement and recording of moisture in building materials such as wood, drywall, roofing, plaster, brick, siding etc. The Survey Encounter incorporates the latest PIC microcontroller to make your job as inspector, surveyor, engineer or architect much more efficient.
Based on micro controller technology it offers data storage, different material libaries, automatic correction for different wood species and temperature. Supplied with PC interface and software compatible with Windows 95/98, 2000 and XP word processing and spread sheet programs.
 |
Benefits
- Non-destructive readings
- Stores up to 625 readings in 25 files
- Accurate moisture readings from 5 to 30% in wood
- Relative readings in walls, roofing and many other construction materials.
- Automatic correction for density and temperature
- Library of 32 wood species plus 3 wall and 3 roofing types
- Dot Matrix LCD display
- Readings can be recalled and displayed on LCD
|
| The Survey Encounter comes complete with customised software and PC interface.
Download recorded readings to your PC.
Transfer stored data to your word-processing or spreadsheet program for analysis or incorporation in your report writing.
Edit any of the 32 wood species in the instrument library from 300 species in the software.
|
Click for Data Sheet
Professional Moisture Meter
The Professional offers a most practical and
accurate way of ensuring that wood is at correct
moisture level for its intended use, proving to
be a vital tool for good quality control.
 |
Benefits
- Uses built-in electronic probes - ready for service
- Built-In socket for use with a range of external electrodes
- Wide measurement range up to 40% in 0.1% increments
- Immediate and accurate readings on a large clear digital LCD display
- Timed On / Off switch, saving battery power.
- Reading Hold facility
- Temperature stable circuit
- Pocket-sized, easy-to-use.
- Heavy-duty, yet light-weight aluminium construction.
- Power source - standard 9v battery included
- Optional calibration check plugs
|
 Also available in Kit form
Click for Data Sheet
Compact Moisture Meter
The Compact is a hand-held instrument
designed to take precise measurements of
moisture content in wood and wood products. Can be used to take comparative readings on other building materials.
The Compact offers a most practical and
accurate way of ensuring that wood is at correct
moisture level for its intended use, proving to
be a vital tool for good quality control.
 | Benefits
- Uses built-in electronic probes - ready for service
- Built-In socket for use with a range of external electrodes
- Wide measurement range up to 40%
- Immediate and accurate readings on a large clear analog display
- Temperature stable circuit
- Pocket-sized, easy-to-use.
- Heavy-duty, yet light-weight aluminium construction.
- Built-in calibration check
- Power source - standard 9v battery included
|
Also available in Kit form
Click for Data Sheet
Concrete Encounter CME4
A pocket size non-destructive meter designed to measure the moisture content
in concrete flooring prior to the application of floor coverings. Simply switch
the CME4 on, hold it against the surface and take readings from the clear analog
dial showing readings up to 6% moisture content. Recommended By Flooring Manufacturers
 |
Benefits:
- Designed, Developed and Calibrated Specifically for Concrete
- Instant Readings
- Measures Up To 6% Moisture Content in Concrete
- Non-Destructive Operation (No Drilling)
- Large Clear Analog Display
- Hold Reading Button
- Battery Operated (Supplied)
- Strong Robust Design
- Pocket Sized
|
Click for Data Sheet
MRH Kit
This is a complete kit for moisture and humidity measurement of the building envelope. It incorporates 3 modes of operation.
 |
Benefits:
- The MRH is a digital display multi featured version of the popular Tramex Moisture Encounter Plus meter. It non-destructively measures percentage moisture content in wood but incorporates a switchable specific gravity adjustment covering wood SG’s of 0.3 to 0.8. Like the MEP it provides relative/comparative readings deep into most building materials such as Dry-wall, Roofing, Brick, Ceramic tile etc.
- Plug in WPIE with Hammer Probe to give accurate moisture readings in wood from 7 to 40%.
- Plug in reusable Relative Humidity Probe for Relative Humidity, Temperature, Dew-Point and Mixing Ratio readings. This RH probe is for measuring ambient conditions or for performing In Situ (ASTM F2170) or RH Hood (ASTM F2420, BS 5325:2001 & BS 8203:2001) methods.
- Instant Readings in non-destructive and wood probe modes
- 5 scales in non-destructive mode including percentage moisture content in wood
- Measures from 7% to 40% Moisture Content in Wood using the plug in WPIE and Hammer Probe with insulated pins.
- Reusable Relative humidity probe provides clear digital display with simultaneous reading for Humidity in both (%RH) and grains/lb. or grams/kg. in addition to Temperature and Dew Point for measuring ambient conditions.
- Reusable Relative Humidity probe can also be used for sub-surface In-Situ method (ASTM F2170) or Non-Destructive Hood Method (ASTM F2420)
- Complies with BS Standard BS5325:2001 and BS 8203:2001 for above surface readings of RH, Temperature and Dew Point readings.
- Detachable 0.4" (10mm) diameter stainless steel RH Probe.
- Intelligent RH Probe can be recalibrated. (Traceable to NIST and international standards.)
- "Hold" feature freezes reading on display.
- Battery Operated (Supplied)
- Die cut foam case allows for addition of Optional extras such as Hand Probe with insulated deep-wall pins, infra-red surface thermometer and a second Tramex moisture meter.
|
Click for Data Sheet
CRH Moisture Content and Relative Humidity Meter for Flooring
The world's most advanced Moisture and Relative humidity Meter for the flooring
industry, the CRH measures Moisture Content by the Non-Destructive Method,
Relative Humidity by the In-Situ Method (ASTM F2170) or Hood method (ASTM
2420-05) and Temperature and Dew Point in concrete and gypsum flooring.
 |
Benefits:
- Measure Moisture Content Non-Destructively into the slab.
- Measure Relative Humidity using the RH Probe on or below the surface.
- Measure temperature and dew point with plug-in RH probe.
- Intelligent RH Probe can be recalibrated. (Traceable to NIST national and
international standards.)
- Stores up to 900 recorded readings in 30 files.
- Recorded readings can be recalled and displayed on dot matrix LCD.
- Download recorded readings to computer for report writing.
- Multiple scales to suit different types of floor slabs and screeds.
- Operates on time proven impedance measurement principle.
- Instant readings on clear Digital display.
|
Also available in Kit form
Click for Data Sheet
IAQ / Mold Remediation Kit
A complete kit for moisture inspection for the IAQ and mold remediation professionals.
 |
Benefits
The IAQ / Mold Remediation Kit contains:
- A non-destructive Moisture Encounter PLUS
- A Professional pin type resistance meter
- A hand held electrode with insulated 7" pins,
- A Digital Hygrometer for temperature, RH% and dew point readings
- Infra-Red Surface Thermometer.
- All of the above in a die cut carrying case.
|
Click for Expanded View
RWS Roof and Wall Moisture Scanner
A multi-mode hand held moisture detection instrument for non-destructive moisture scanning, surveying, and leak tracing in the building envelope, including built up, non-conductive single ply membranes, modified and foam roofing systems and EIFS (Exterior Insulation Finishing Systems) with a non-conductive roof membrane. This instrument is a combination of the popular Tramex Leak-Seeker and the Wet Wall Detector at a great price.
 |
Benefits:
- Built-Up
- Non-Conductive Single Ply
- Modified and Foamed Roofing Systems
- Exterior Insulation and Finishing Systems (EIFS)
|
Also available in Kit form
Click for Data Sheet
Digital Hygrometer
For fast and accurate measurement of relative humidity, temperature and dew point of the environment. Excess humidity for long periods of time may contribute to Mold growth.
 |
Benefits
- Micro processor-based design.
- Sensor: electronic capacitance polymer film.
- Fast reacting (approx 60 secs) High Accuracy
- Measures Temperature Centigrade & Fahrenheit, -20° C to 50° C (14° F to 120° F).
- Measures Relative humidity 5% to 95%
- Electronically calculated Dew point
- Measures Min/Max
- Data Hold freezes reading.
- Pocket size
- Model 8705 sames as above but also electronically calculates Wet bulb temperature
|
Click for Expanded View
Infra-Red Surface Thermometer
 |
- Precise non-contact Measurements
- Switchable °C/°F Temperature Units
- Automatic Data Hold
- Laser Target Pointer (switchable On/Off)
- 8:1 Distance Spot Ratio
- Large Digital LCD Display
- Measuring Range -4° - 788° F
- Wide Range of Applications: Flooring, Roofing, Marine, HVAC
|
Click for Expanded View
|
